User's Manual
Digital Display Alcohol Concentration Test Meter
Model: AD-6000NS

Precaution 1
------------
Thank you for selecting and purchassing AD-6000NS Digital Display Alcohol
Concentration Test Meter. Please read this manual carefully to ensure that you can
use the product correctly.

This device is a healthcare product; it is intended to control overdrink of alcohol
so as to keep you fit, through testing the alcohol in your breath and calculating
the content of alcohol via microcomputer. The product is applicable
to family healthcare as well as for reference in determining whether the driver is
driving after drinking.

The test result may be affected by a number of aspects such as environmental
temperature, various gases in the air and smoking, etc. the result shall, therefore,
be only for reference and shall not be regarded as the justification of driving
after drinking.

No matter whether you have consumed this product, its manufactured and
appropriate agents shall be not responsible for any traffic accident arisen due to
ethanol or other accidents happened under therelated regulations and rules.

As people's breath contains some fermentable gases (from stomach and
intestines), so some gases may even be tested out under no drink circumstance.

When after drinking, it is recommended to last after 20 minutes, it is because 20
minutes is approximately for alcohol to be absorbed into blood from the
digestive organs, and residual alcohol remaining in the mouth takes this long to
dissipate.

For accurate result, do not repeat neat testing with in 3 minutes after time.

Do not somke and eat for 20 minutes prior testing.

Do not use any excitant substances near the tester, such as paing, insecticedes, alcohol.

If the device has been performed for five times successively, please stop for two
minutes and then use it again.

Do not drive after drinking!

Preparation Before Using 2
--------------------------
After opening the package, please check the parts and components below. If any
one is absent, please contact its dealer.

Accessories
1.One AD-6000NS LED digital display alcohol concentration detector
2.One User Manual
3.Three AA alkaline batteries. (not included)
4.6 air-blowing pipes.

Battery Installation
Install two 1.5V AA alkaline batteries with same specification
into the battery case in a right way (as shown in figure 1) per the mark "+" and
"-" on the case, and then close the cover well (as shown in figure 2)

Battery Replacement
If the yello LED on the LCDflashes, it indicates the battery electricity is not
enough end the batteries need tobe replaced, in order to ensure the test accuracy.
Open the attery cover end take out the batteries, and reinstall the new batteries
with same specification (as shown in figure 3). Make sure to keep the old
batteries out of children's reach, please dispose the useless batteries according to
the local regulations.

How to use the alcohol tester 3
-------------------------------
Operational Procedure:
Wait
Press the power button about 2 seconds, the alcohol tester LCD will tun on with
one beep sound.
The: "wark up" symbol is displayed and the 150 to 000 (or 15 to 00) countdown is
stared that indicate the testeris in wark up mode.
NOTE
If first wark up is defeated, the tester will be reset automatically and wark up
again for 1-3 times.
It always has a large number of gaz & impurity adsorbed on the surface of
alcohol sensor, when first time taking out the tester from the packaging, or after
long time no using for the tester, it need more time for cleaning and wark up the
alcohol sensor, you shouldrepress the power button and retry several times If
possible.
TEST
The "BLO" symbolis displayed when wark-up is succeed, and the 100 to 000
countdown is stared that indicate the tester is in testing mode.
Near and blow into the breath inhale for 3-5 seconds.
Read the tester result from the alcohol tester lcd.
Push the power button and hold 3s, the buzzer sound "B" one times, it is
warming up and counting down from 150 about 15s. It will start to "BLOW"
when it count down to "000"
It will sounds and the grenn LED will light on and display "BLO" after counting
down, it means you can start to test. "BLO" will shine about 10s. Confirm to
blow within this 10s.
Blow to the breath inlet about 5s, There is a long sound if there is alcohol, and it
will display 003,002,001. After this, the result will show on. Only green LED
shines and there are short sound "B,B,B" if the result is between 0.00-0.05. Only
red LED shines and there are long sound "B,B,B" if the result is more than 0.05.
The result will remain 15s, and then it will turn off.

If there is no alcohol, it will display 0.00 after 10s shining "BLO".
If will auto turn off if there is no alcohol or no testing within 30s after turning on.

Auto power off 4
----------------
1. After the result be display for about 10 seconds, the "off" symbol will
   appear 2 seconds and the alcohol tester be turned off.
2. If wark up is defeated, the tester will automatically turned off.

EOF